Talent 101 Circuit

Dipta – Electrical Engineer

• Worked on developing a DC-DC boost converter to be used for consumer electronics using IBM 0.18um technology
• Studied and redesigned different DC-DC boost topologies to achieve maximize voltage efficiency
• Assisted Ph.D. candidates and other graduate students with PCB layout design for their research projects
• Aided Ph.D. candidates with designing components of PLL (phase locked loop) like VCO (voltage controlled oscillator) and filters
• IC Design Tools:  Cadence Virtuoso, Synopsys DC, Cadence Assura (DRC, LVS,QRC), Cadence Encounter, OrCAD, Altera Quartus II, Multisim, Altium Circuit Maker, LabVIEW

Gilberto – Electrical Engineer  

• Electrical Engineer with total 5+ years of engineering experience
• Excellent knowledge of digital and analog system design and testing
• Extensive knowledge of the design concepts and applications of signal processors, ASIC Design & Verification, Microprocessors and very-large-scale integration circuit systems

Srikanth – Electrical Engineer  

• Academic experience in ASIC/ SoC RTL Design (with Verilog HDL and System Verilog) and Functional Verification.
• Hands-on experience of RTL Logic Synthesis, Static Timing Analysis (STA), Power Analysis and Optimization
• VLSI Proficiency:  ASIC and FPGA Design flow, Physical Design flow (Floor planning, Placement, CTS and Routing), Physical Verification, Signal Integrity and CMOS IC Design, Characterization, Simulation and Layout

Sydney - Electrical Engineer   

• ASIC design experience in taking designs from the preliminary netlist step through tape out.
• ASIC/FPGA development skills including: logic simulation, formal verification, static timing analysis, floor planning, place and route, timing closure, test vector generation, power analysis, signal integrity checks, LVS/DRC checks, limited logic synthesis and overall EDA methodology/flow compatibility issues.

George - Electrical Engineer  

Changpu – Characterization Engineer

• Developed and completed the following items for DC/DC Buck converter characterization and verification:
• Characterization Plan
• Used Cadence Capture/Allegro to Design the Schematic and Layout for Evaluation board
• Bench Hardware Setup
• LabVIEW GUI
• Failure Analysis on the Hardware

Maha - Electrical Engineer

• VLSI design
• Advanced Digital LogicM
• Testing and Testable design of VLSI
• Computer architecture
• Analog IC design
• RF and Microwave Amplifier design
• Digital Signal Processing
• Master of Science – Electrical Engineering

Diego – Senior Electrical Engineer  

• Development and implementation of service tool communication protocol for communication.
• New Product Development.
• Communication protocol development in embedded C controls.
• Developing device driver and BSP.
• Development of Real Time embedded software.
• Software architectures.
• Digital Signal Processing.
• Serial communications UART, I2C, Modbus, CAN bus and peripheral interfaces.
• Integration of protocol stacks.
• Analog and digital circuit controls hardware test and design.
• BS in Electrical Engineering.

Ting – Senior Electronics/Electrical Systems Engineer

• Electrical/Electronic Design & Production Engineering.
• Electro-Mechanical Design.
• Project Management experience in Avionics, BOP Control Systems, Industrial Equipment, Semiconductor Capital Equipment, and Telecommunications.
• Lead for the BOP Control Systems product line.
• Managed product development engineering, Manufacturing Equipment Solutions (MES), functional test development for cables/harnesses, and tool crib activities.
• Manufacturing engineering support for the battery pack assembly area.
• Masters of Engineering in Electrical Engineering.

Paul – Senior Electrical Engineer  

• Electronic/RF/Microwave Communications and Navigation Product and System Conceptualization and Design.
• New Product Development.
• Mechanical Product Design.
• Electronic Equipment Manufacturing.
• Procurement of Electrical and Electronics System Components.
• Sustaining Engineering.
• Facilitation of Tech Startups/Spinoffs.
• ERP/MRP System Installation and Configuration.
• Offshore Component and CEM Sourcing and Vendor Interface.
• Manufacturing Cost Reduction.
• Quality Assurance (5S, TQM, 8D, Five Why's) System Implementation (including facilitation of upgrade to ISO 9001/AS9100C compliant manufacturing and engineering organizations).
• 8x/4x material cost reduction expert.
• B.S. in Electrical and Electronics Engineering.